Speed Queen Er FL: the machine did not reach its fill level
Speed Queen’s own manual states this code appears if the washer has not reached the fill level after 30 minutes during a wash or rinse fill, which on a first installation is most often traced to a faucet not yet turned on or a kinked hose.
Mon–Sat, 8am–8pm
- Water supply and drain
- Water supply and shutoff connection
- Source: Speed Queen
Book a visit
Three short steps, about a minute.
or call (844) 638-8309
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Er FL
actually means.
Speed Queen’s own manual states this code appears if the washer has not reached the fill level after 30 minutes during a wash or rinse fill, which on a first installation is most often traced to a faucet not yet turned on or a kinked hose.
Speed Queen appliance display · also shown as Er, FL
What to do when Er FL shows on the applianceKind of codeWater supply and drain
The new appliance is reporting what it gets from the water connections behind it. A no-water or slow-fill message on the first fill usually means the supply valve is still closed or only half open, or the new line kinked when the unit slid back; a drain message means the drain hose is pinched, pushed too deep into the standpipe, or looped higher or lower than the installation instructions allow. Open the valve fully, straighten the hose, set it to the height the manual gives, and run the cycle again.
Usually leads toWater supply and shutoff connection
New supply lines from a working quarter-turn stop to each water appliance, tested under pressure.
Shows up asAppliance Installation Code on a New Unit: Setup Modes and Hookup Messages
An appliance installation code is a message a new unit shows because of how it was set up: a demo mode, a water or drain alert, a vent warning or a power check.
MakeSpeed Queen
Speed Queen installs are laundry only: heavy top-load and front-load washers and gas or electric dryers, connected, leveled and vented outside.
SourceSpeed Queen use & care manual, Part No. 808187ENR4
Confirmed on Speed Queen’s own top-load washer use-and-care manual (Part No. 808187ENR4); the commercial-grade platform documents the equivalent as "E FL" with the same 30-minute window.
Before you book,
in this order.
Each step comes from Speed Queen's own guidance for Er FL on its appliances. Follow it to the end: the last card says whether this is a visit.
Make sure both hot and cold water faucets behind the machine are turned fully on.
Check that the fill hoses are not kinked or twisted along their run.
Clean the screens in the water mixing valve and the filter screens at the faucet end of the fill hoses.
Unplug the machine for 15 seconds to clear the code and run a test cycle; if Er FL returns with faucets open and hoses clear, book a visit.
Still there?
It usually turns into water supply and shutoff connection. Book with the code and the model number.
What not to do
Er FL is a fill-timing alert, not a drain or spin-balance problem — water never reaching the tub is the tell, as opposed to water reaching it and then not draining out. If faucets and hoses check out and the code repeats, that points elsewhere.
What you may
notice with it.
The appliance problems Er FL tends to arrive with. Answer these at the appliance before anyone is booked.
All problems
Where Er FL usually leads
Water supply and shutoff connection.
Speed Queen
appliances.
Speed Queen installs are laundry only: heavy top-load and front-load washers and gas or electric dryers, connected, leveled and vented outside.
Speed Queen appliance installationMore Speed Queen codes
Water supply and drain on other makes
In Speed Queen's own words
This code will appear if the washer has not reached the fill level after 30 minutes during a wash or rinse fill.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Confirmed on Speed Queen’s own top-load washer use-and-care manual (Part No. 808187ENR4); the commercial-grade platform documents the equivalent as "E FL" with the same 30-minute window.
Speed Queen Er FL appliance installation,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Er FL.
Can I clear Er FL myself?
My newly installed Speed Queen laundry machine shows Er FL — did the installer forget something?
How long does a Speed Queen machine wait before showing Er FL?
I confirmed the faucets are on and the hoses are straight, but Er FL keeps showing — what else could it be?
Back to your everyday
Still showing Er FL?
A booking moves faster with three things: the message exactly as the display shows it, the model number from the carton or the rating plate, and the moment it first appeared. With those, the office can tell whether it is a setup step or a connection to put right, and send the part that fixes it.