Asko F11: drain hose fit on a dish care machine
ASKO's own manual ties this alert to the coarse and fine filters, a blocked drain pump, and specifically whether the drain hose was fitted in accordance with the installation instructions.
Mon–Sat, 8am–8pm
- Water supply and drain
- Water supply and shutoff connection
- Source: ASKO
Book a visit
Three short steps, about a minute.
or call (844) 638-8309
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F11
actually means.
ASKO's own manual ties this alert to the coarse and fine filters, a blocked drain pump, and specifically whether the drain hose was fitted in accordance with the installation instructions. That last point ties the alert directly to the hookup rather than to a part that wears out.
ASKO appliance display · also shown as F68
What to do when F11 shows on the applianceKind of codeWater supply and drain
The new appliance is reporting what it gets from the water connections behind it. A no-water or slow-fill message on the first fill usually means the supply valve is still closed or only half open, or the new line kinked when the unit slid back; a drain message means the drain hose is pinched, pushed too deep into the standpipe, or looped higher or lower than the installation instructions allow. Open the valve fully, straighten the hose, set it to the height the manual gives, and run the cycle again.
Usually leads toWater supply and shutoff connection
New supply lines from a working quarter-turn stop to each water appliance, tested under pressure.
Shows up asDrain Backing Up After an Install: Plug, Loop and Standpipe
A drain backing up after an install leaves water standing in a new machine, pushes it into the sink or spills it over the top of the standpipe.
MakeASKO
ASKO installs mean a compact Scandinavian dish care machine or laundry pair, set level and stacked with the maker's own kit where space is short.
SourceASKO US dishwasher instructions for use, document 875097en
Confirmed in ASKO's US dishwasher instructions for use and installation manual (document 875097en); a related BLDC drain pump alert, F68, is documented in the same table.
Before you book,
in this order.
Each step comes from ASKO's own guidance for F11 on its appliances. Follow it to the end: the last card says whether this is a visit.
Clean the coarse and fine filters inside the machine, following ASKO's own care instructions.
Run any dishwashing program to see whether the alert clears once the filters are clean.
Check the drain hose against ASKO's own installation instructions for its height and routing, since the manual names this directly as a cause.
If the filters are clean and the hose is correctly fitted, book a visit.
Still there?
It usually turns into water supply and shutoff connection. Book with the code and the model number.
What not to do
F11 does not automatically mean the drain pump has failed. ASKO's own manual lists a misfitted drain hose ahead of a pump problem, so the hookup is checked first.
What you may
notice with it.
The appliance problems F11 tends to arrive with. Answer these at the appliance before anyone is booked.
All problems
Where F11 usually leads
Water supply and shutoff connection.
ASKO
appliances.
ASKO installs mean a compact Scandinavian dish care machine or laundry pair, set level and stacked with the maker's own kit where space is short.
ASKO appliance installationMore ASKO codes
Water supply and drain on other makes
Cold storage
Setting a new refrigerator, freezer, wine or beverage unit or ice maker into its opening: measured, connected to water, leveled and started.
Dish care
Fitting a new dishwasher or dish drawer under the counter: supply line, drain loop or air gap, power, mounting brackets and a first test cycle.
Laundry
Setting up a new washer, dryer or stacked pair: shipping bolts out, hoses on, drain and exhaust run connected, power checked and the machines leveled.
In ASKO's own words
Check that the drain pump is not blocked. Also check that the drain hose is fitted in accordance with the installation instructions.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Confirmed in ASKO's US dishwasher instructions for use and installation manual (document 875097en); a related BLDC drain pump alert, F68, is documented in the same table.
ASKO F11 appliance installation,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F11.
Can I clear F11 myself?
I cleaned the filters and F11 is still showing. What's left to check?
Is F68 the same alert as F11?
Can a wrongly fitted drain hose really cause an alert instead of just a slow drain?
Back to your everyday
Still showing F11?
A booking moves faster with three things: the message exactly as the display shows it, the model number from the carton or the rating plate, and the moment it first appeared. With those, the office can tell whether it is a setup step or a connection to put right, and send the part that fixes it.