The back of a newly installed dryer pulled a little away from a laundry room wall, a short rigid metal exhaust duct joined to the dryer's outlet with a clamp and running straight to the wall, the floor behind swept clean, nobody in the frame.

LG d90 — a graded duct blockage reading on a new hookup

LG's own help library explains that d90 or d95 mean the dryer has detected a 90 or 95 percent blockage in the duct work, and specifically warns not to use the dryer until the exhaust system has been cleaned and repaired.

(844) 638-8309

Mon–Sat, 8am–8pm

  • Vents and ducting
  • Laundry exhaust run installation
  • Source: LG

Book a visit

Three short steps, about a minute.

or call (844) 638-8309

What d90
actually means.

LG's own help library explains that d90 or d95 mean the dryer has detected a 90 or 95 percent blockage in the duct work, and specifically warns not to use the dryer until the exhaust system has been cleaned and repaired.

LG appliance display · also shown as d95, d80, d75

What to do when d90 shows on the appliance

Before you book,
in this order.

Each step comes from LG's own guidance for d90 on its appliances. Follow it to the end: the last card says whether this is a visit.

01

Confirm the lint filter itself is clean before assuming the duct run is the cause.

02

Check for airflow at the outside vent while a cycle is running.

03

Disconnect and inspect the full duct run for obstructions, including anywhere it was crushed or kinked during installation.

04

Do not run the dryer again until the exhaust system is confirmed clear and repaired, per LG's own warning.

Still there?

It usually turns into laundry exhaust run installation. Book with the code and the model number.

What not to do

d90 does not mean the heating element or the drum motor has failed. LG's own explanation points entirely at the exhaust duct outside the cabinet, which is an installation and maintenance detail rather than a part inside the unit.

Where d90 usually leads

Laundry exhaust run installation.

Metal exhaust transition and reachable wall run fitted from a new dryer to the outside hood, joints taped, airflow confirmed · moderate.

In LG's own words

If you see a d90 or d95 error on your control panel, your dryer has detected a 90% or 95% blockage in the duct work, prompting immediate attention.
LG USA Support — Understanding d90 and d95 Error Codes

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. LG documents a graded scale from d75 through d95 on the same dryer platform, with severity increasing toward d95.

LG d90 appliance installation,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas
A family unpacking groceries into a newly fitted kitchen, the fresh appliances set flush in their openings.
For the heart of your home.

Questions
about d90.

Can I clear d90 myself?
Confirm the lint filter itself is clean before assuming the duct run is the cause. If it comes back, it needs a visit.
Can a brand-new duct run already read as 90 percent blocked?
Yes, if the run is too long, has too many tight turns, or was crushed while the unit was pushed into place, a new hookup can show this reading on its very first cycle.
Is it safe to keep drying loads while d90 is showing?
No, LG's own warning is not to use the dryer until the exhaust system has been cleaned and repaired, since a heavily restricted duct affects both drying performance and heat buildup.
How is d90 different from d75 or d80?
They are all the same graded reading at different severities — LG's scale reports roughly 75, 80, or 90-95 percent blockage — so a lower number is still worth checking even though it is less urgent than d90 or d95.

Back to your everyday

Still showing d90?

A booking moves faster with three things: the message exactly as the display shows it, the model number from the carton or the rating plate, and the moment it first appeared. With those, the office can tell whether it is a setup step or a connection to put right, and send the part that fixes it.

(844) 638-8309 Schedule an installation