Frigidaire SB SB — Sabbath mode on a cold storage unit
Frigidaire's own support article describes SB SB as Sabbath Mode, a feature that disables portions of the unit and its controls in accordance with observance of the weekly Sabbath and religious holidays, while specifically noting the high-temperature alarm stays active for food-safety reasons.
Mon–Sat, 8am–8pm
- Setup modes, not failures
- No installation needed
- Source: Frigidaire
Book a visit
Three short steps, about a minute.
or call (844) 638-8309
Loading appointment form…
The appointment form couldn’t load. Please try again.
What SB SB
actually means.
Frigidaire's own support article describes SB SB as Sabbath Mode, a feature that disables portions of the unit and its controls in accordance with observance of the weekly Sabbath and religious holidays, while specifically noting the high-temperature alarm stays active for food-safety reasons.
Frigidaire appliance display · also shown as Sb
What to do when SB SB shows on the applianceKind of codeSetup modes, not failures
Nothing is wrong with the new appliance; it has come out of the carton in a state the store or the factory left it in. A showroom or demo mode lights the display and the fans while the unit never cools or heats, a Sabbath setting holds the oven light and hides the controls, a control or shipping lock refuses every key, and some laundry and dish care machines ask for a first calibration cycle before normal use. The manual gives the key sequence that turns each one off; once it is off, the appliance runs as it should.
Usually leads toNo installation
Confirm the household intends this mode to be active before assuming the panel has stopped responding.
Shows up asCold Storage Slow to Cool on the First Day
Cold storage slow to cool is a new refrigerator, freezer, wine or beverage unit that still feels warm inside many hours after its installation.
MakeFrigidaire
Frigidaire installs are usually straight swaps: a refrigerator, range, dishwasher or laundry pair going onto the hookups the old one used.
SourceFrigidaire owner support — Error Code SB SB (Sabbath Mode)
Frigidaire documents this exact display and button combination on its standard cold storage electronic control platform.
Before you book,
in this order.
Each step comes from Frigidaire's own guidance for SB SB on its appliances. Follow it to the end: the last card says whether this is a visit.
Confirm the household intends this mode to be active before assuming the panel has stopped responding.
Use the documented button combination to deactivate it, which Frigidaire describes as holding the minus and Temp F-C buttons together for five seconds.
Check that the dispenser and lights return to normal once the mode is cleared.
If the display will not exit Sabbath mode with the documented sequence, book a visit rather than repeatedly cycling power.
Cleared?
The message has gone from the display, the setting or connection behind it has been corrected, and the new appliance finishes a full first cycle without raising it again. A setup code that comes straight back after the hookup has been checked points to something the install missed, such as a kinked hose or a harness left unplugged, so note it when you book.
What not to do
SB SB does not mean the control board or the dispenser has failed; those controls are deliberately non-functional while the mode is active. It does not silence every alert either, since the high-temperature alarm is documented to remain live.
What you may
notice with it.
The appliance problems SB SB tends to arrive with. Answer these at the appliance before anyone is booked.
All problems
No installation indicated
Nothing to install.
Nothing is wrong with the new appliance; it has come out of the carton in a state the store or the factory left it in. A showroom or demo mode lights the display and the fans while the unit never cools or heats, a Sabbath setting holds the oven light and hides the controls, a control or shipping lock refuses every key, and some laundry and dish care machines ask for a first calibration cycle before normal use. The manual gives the key sequence that turns each one off; once it is off, the appliance runs as it should.
Frigidaire
appliances.
Frigidaire installs are usually straight swaps: a refrigerator, range, dishwasher or laundry pair going onto the hookups the old one used.
Frigidaire appliance installationMore Frigidaire codes
Setup modes, not failures on other makes
Cold storage
Setting a new refrigerator, freezer, wine or beverage unit or ice maker into its opening: measured, connected to water, leveled and started.
Cooking appliances
Hooking up ranges, cooktops, wall ovens, microwaves and hoods: gas connectors leak-tested, anti-tip brackets fastened, ducts sized and the first light checked.
Dish care
Fitting a new dishwasher or dish drawer under the counter: supply line, drain loop or air gap, power, mounting brackets and a first test cycle.
In Frigidaire's own words
The Sabbath Mode is a feature that disables portions of the refrigerator and its controls in accordance with observance of the weekly Sabbath and religious holidays within the Orthodox Jewish community.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Frigidaire documents this exact display and button combination on its standard cold storage electronic control platform.
Frigidaire SB SB appliance installation,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about SB SB.
Can I clear SB SB myself?
Will a Frigidaire cold storage unit still warn me if it warms up while in Sabbath mode?
Why would a new unit already be in Sabbath mode at delivery?
Does Sabbath mode stop the unit from cooling?
Back to your everyday
Still showing SB SB?
A booking moves faster with three things: the message exactly as the display shows it, the model number from the carton or the rating plate, and the moment it first appeared. With those, the office can tell whether it is a setup step or a connection to put right, and send the part that fixes it.