GE Profile SAb — Sabbath mode on a dish care machine
GE Profile's own manual documents SAb as the display shown when Sabbath Mode is active, entered or exited by pressing and holding Lock and Light simultaneously for five seconds.
Mon–Sat, 8am–8pm
- Setup modes, not failures
- No installation needed
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 638-8309
Loading appointment form…
The appointment form couldn’t load. Please try again.
What SAb
actually means.
GE Profile's own manual documents SAb as the display shown when Sabbath Mode is active, entered or exited by pressing and holding Lock and Light simultaneously for five seconds.
GE Profile appliance display · also shown as Sabbath Mode
What to do when SAb shows on the applianceKind of codeSetup modes, not failures
Nothing is wrong with the new appliance; it has come out of the carton in a state the store or the factory left it in. A showroom or demo mode lights the display and the fans while the unit never cools or heats, a Sabbath setting holds the oven light and hides the controls, a control or shipping lock refuses every key, and some laundry and dish care machines ask for a first calibration cycle before normal use. The manual gives the key sequence that turns each one off; once it is off, the appliance runs as it should.
Usually leads toNo installation
Confirm whether the household intends this mode to be active before assuming the panel has failed.
Shows up asAppliance Installation Code on a New Unit: Setup Modes and Hookup Messages
An appliance installation code is a message a new unit shows because of how it was set up: a demo mode, a water or drain alert, a vent warning or a power check.
MakeGE Profile
GE Profile installs include combination washer-dryers that need only an outlet and a drain, plus refrigeration, ranges, wall ovens and dishwashers.
SourceGE Profile dishwasher owner's manual — Sabbath Mode
GE Profile documents this exact button combination on its standard electronic dishwasher control panel.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for SAb on its appliances. Follow it to the end: the last card says whether this is a visit.
Confirm whether the household intends this mode to be active before assuming the panel has failed.
Use the documented Lock-and-Light hold to exit the mode if it was set by mistake during setup or in the store.
Confirm normal cycle operation once the mode is cleared.
If SAb will not clear with the documented sequence, book a visit rather than repeatedly power-cycling the unit.
Cleared?
The message has gone from the display, the setting or connection behind it has been corrected, and the new appliance finishes a full first cycle without raising it again. A setup code that comes straight back after the hookup has been checked points to something the install missed, such as a kinked hose or a harness left unplugged, so note it when you book.
What not to do
SAb does not indicate the keypad or the electronic control has failed. It is a deliberate setting, and GE Profile documents exactly how it is entered and exited on this control platform.
What you may
notice with it.
The appliance problem SAb tends to arrive with. Answer these at the appliance before anyone is booked.
All problems
No installation indicated
Nothing to install.
Nothing is wrong with the new appliance; it has come out of the carton in a state the store or the factory left it in. A showroom or demo mode lights the display and the fans while the unit never cools or heats, a Sabbath setting holds the oven light and hides the controls, a control or shipping lock refuses every key, and some laundry and dish care machines ask for a first calibration cycle before normal use. The manual gives the key sequence that turns each one off; once it is off, the appliance runs as it should.
GE Profile
appliances.
GE Profile installs include combination washer-dryers that need only an outlet and a drain, plus refrigeration, ranges, wall ovens and dishwashers.
GE Profile appliance installation
Cold storage
Setting a new refrigerator, freezer, wine or beverage unit or ice maker into its opening: measured, connected to water, leveled and started.
Cooking appliances
Hooking up ranges, cooktops, wall ovens, microwaves and hoods: gas connectors leak-tested, anti-tip brackets fastened, ducts sized and the first light checked.
Dish care
Fitting a new dishwasher or dish drawer under the counter: supply line, drain loop or air gap, power, mounting brackets and a first test cycle.
In GE Profile's own words
Sabbath Mode: Press and hold Lock and Light simultaneously for 5 seconds to enter or exit Sabbath mode. Display will show SAb when in Sabbath mode.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile documents this exact button combination on its standard electronic dishwasher control panel.
GE Profile SAb appliance installation,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about SAb.
Can I clear SAb myself?
Why would a new dish care machine already show SAb before it has been used?
Does SAb disable the whole panel or just some functions?
Is the SAb button combination the same on every GE Profile dish care machine?
Back to your everyday
Still showing SAb?
A booking moves faster with three things: the message exactly as the display shows it, the model number from the carton or the rating plate, and the moment it first appeared. With those, the office can tell whether it is a setup step or a connection to put right, and send the part that fixes it.