Samsung Cb — a laundry machine calibrating itself
Samsung's own troubleshooting page describes Cb and C6 as calibration mode, used to recalibrate the weight detection of the washer, a normal step rather than any kind of malfunction.
Mon–Sat, 8am–8pm
- Setup modes, not failures
- No installation needed
- Source: Samsung
Book a visit
Three short steps, about a minute.
or call (844) 638-8309
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Cb
actually means.
Samsung's own troubleshooting page describes Cb and C6 as calibration mode, used to recalibrate the weight detection of the washer, a normal step rather than any kind of malfunction.
Samsung appliance display · also shown as C6
What to do when Cb shows on the applianceKind of codeSetup modes, not failures
Nothing is wrong with the new appliance; it has come out of the carton in a state the store or the factory left it in. A showroom or demo mode lights the display and the fans while the unit never cools or heats, a Sabbath setting holds the oven light and hides the controls, a control or shipping lock refuses every key, and some laundry and dish care machines ask for a first calibration cycle before normal use. The manual gives the key sequence that turns each one off; once it is off, the appliance runs as it should.
Usually leads toNo installation
Let the calibration cycle run to completion without interrupting it.
Shows up asAppliance Installation Code on a New Unit: Setup Modes and Hookup Messages
An appliance installation code is a message a new unit shows because of how it was set up: a demo mode, a water or drain alert, a vent warning or a power check.
MakeSamsung
Samsung installs cover refrigerators with ice and water, slide-in ranges, dishwashers and laundry pairs, often joined to a home network at first power-on.
SourceSamsung support — Samsung washer error codes (calibration mode)
Samsung documents Cb/C6 as calibration mode on its current washer control platform.
Before you book,
in this order.
Each step comes from Samsung's own guidance for Cb on its appliances. Follow it to the end: the last card says whether this is a visit.
Let the calibration cycle run to completion without interrupting it.
Avoid opening the door or adding items while calibration is in progress.
Confirm normal cycle operation once calibration finishes.
If Cb repeats on every subsequent cycle rather than clearing after the first run, book a visit.
Cleared?
The message has gone from the display, the setting or connection behind it has been corrected, and the new appliance finishes a full first cycle without raising it again. A setup code that comes straight back after the hookup has been checked points to something the install missed, such as a kinked hose or a harness left unplugged, so note it when you book.
What not to do
Cb does not indicate a weight sensor has failed. Samsung documents it as a deliberate recalibration step, most commonly seen the first few times a new machine is used.
What you may
notice with it.
The appliance problem Cb tends to arrive with. Answer these at the appliance before anyone is booked.
All problems
No installation indicated
Nothing to install.
Nothing is wrong with the new appliance; it has come out of the carton in a state the store or the factory left it in. A showroom or demo mode lights the display and the fans while the unit never cools or heats, a Sabbath setting holds the oven light and hides the controls, a control or shipping lock refuses every key, and some laundry and dish care machines ask for a first calibration cycle before normal use. The manual gives the key sequence that turns each one off; once it is off, the appliance runs as it should.
Samsung
appliances.
Samsung installs cover refrigerators with ice and water, slide-in ranges, dishwashers and laundry pairs, often joined to a home network at first power-on.
Samsung appliance installation
Cold storage
Setting a new refrigerator, freezer, wine or beverage unit or ice maker into its opening: measured, connected to water, leveled and started.
Cooking appliances
Hooking up ranges, cooktops, wall ovens, microwaves and hoods: gas connectors leak-tested, anti-tip brackets fastened, ducts sized and the first light checked.
Dish care
Fitting a new dishwasher or dish drawer under the counter: supply line, drain loop or air gap, power, mounting brackets and a first test cycle.
In Samsung's own words
Calibration mode is used to recalibrate the weight detection of the washer.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Samsung documents Cb/C6 as calibration mode on its current washer control platform.
Samsung Cb appliance installation,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Cb.
Can I clear Cb myself?
Why does a brand-new laundry machine run a strange short cycle before I can wash anything?
How long does Samsung's calibration mode usually take?
Does calibration mode need to be run again after the machine has been moved?
Back to your everyday
Still showing Cb?
A booking moves faster with three things: the message exactly as the display shows it, the model number from the carton or the rating plate, and the moment it first appeared. With those, the office can tell whether it is a setup step or a connection to put right, and send the part that fixes it.